base

I just noticed that my mast base plate is slightly out of alignment by a few degrees. I assume this is factory because the original screw holes are the only ones present. Of course nothing on the boat is exactly lined up, based on some simple string measurements, but this seems like it needs to...

Any one know of a used Y S pedestal for Sale? The base on our E 38 is cracke from one of the mounting holes and needs to be replaced. We are not doing any extended stuff this year due to a new job, so I have some time... Thanks, Harold, S/V Mischief Maker

Senta has a ~5' emergency tiller. Looking at that beautiful long tiller I don't see how it could possibly be used in the small space behind the pedestal. Yet, the only access hatch in the pedestal is in the aft part of the pedestal base. I hope the pictures below show that reasonably well...

I just removed my stanchions and bases to reseal them and found some water standing in the base. I thought of just drilling a small hole at the lower end of it to let the water out but was wondering if someone has a better idea

Anyone have ideas on baseline tension on the bobstay, headstay, backstay and upper shrouds on the Independence 31? Here are my issues: 1) I feel like I have an issue with my bowsprit lifting (can see a gap at the stem), which would indicate perhaps bobstay stretch and need of tensioning, 2)...

Greetings fellow E34T owners. Would anyone have anything more specific on the rig tension settings. I have referred to the manual, but would welcome any comments or thoughts. Thank you kindly,:egrin: Tom Chicago, IL

Few days ago, I noticed that one of the bolts holding the port-side rope clutch (serves jib and spinnaker halyards) is leaking ... I took it out, then noticed that the wooden block which the rope clutch sits on is in bad shape - the forward edge (in the direction of pull) has started to crumble...

Does anyone know a good source for a 2-3/8" flange base for an aluminum radar post mounted on the transom? The Navcom flange base mounts sold by Edson are $80. I also need a rail bracket for the 2-3/8" aluminum post, which costs about $120 at Edson. $200 for both is on the high side. Thanks...

Hello, The base of the pedestal on my E-38 is badly corroded (see pics). Can this be repaired? If it needs replaced, does anyone have any experience or ideas to replace it? Can I just replace the base or does the entire pedestal have to be replaced? Thanks! John

I'm installing Andersen 40 ST winches port and starboard on the cabin top. The base on these winches is a higher profile than the Barients I removed. I'd like to raise the rope clutches about half an inch with some kind of base. I thought of using starboard but I'm concerned that starboard's...

HI, everyone. I am in need of a spreader base bracket, (Port side) broke mine a couple days ago while climbing to install a windex. So far i have had no luck in finding this piece anywhere, places i have called are pacific seacfraft, RigRight, LeFiell manufacturing. Any help or sugestions...

HI, everyone. I am in need of a spreader base bracket, (Port side) broke mine a couple days ago while climbing to install a windex. So far i have had no luck in finding this piece anywhere, places i have called are pacific seacfraft, RigRight, LeFiell manufacturing. Any help or sugestions...

Looking for replacement pedestal base for Erickson 30 plus. Any thoughts appreciated. RichardSF

Have Erickson 30 plus with substantial deterioration of pedestal base. Any ideas on where to obtain replacement part or repair??

I have a 1985; 32-300 My flooring around the mast has delaminated and generally rotted an area about a foot square. Rot has also wicked up the side of the adjacent locker. Rain water evidently accesses the inside of the mast and should be routed to the bilge via a coffer at the base of the...

Any one have any ideas about where to get a spreader base mast fitting for my 1976 E23. I broke my starboard one this last week while putting up the mast. I have manufactured a temporary one from steel, but won't really trust it in a blow. Thanks for any response. Great Forum.