pulpit

Hi, I have a damaged pulpit on an E-29 (1972). The pulpit is bent on one side and I am not sure if it can be repaired, I am looking into it with a local machine shop. My question is, would this be a custom order to replace or is it a stock item still in production? If custom, any thoughts...

I am relocating the bow lights to the pulpit and am wondering about how to seal the holes I will have to drill (or, figure out a way to make sure it all drains out somehow). The wires will enter at the top and exit on the aft stanchion base on the port side. If any water gets in it will travel...

Had a great week of sailing last week out of New Bedford, to Elizabeth Islands and to Martha's Vineyard. I've got a rigging question. My boat is 1980 E-25+, furling genoa. When genoa is out, it is (in almost all circumstances) pushed right into the pulpit rail. So the bottom couple feet of...

Recently purchased an E35-MKIII that had storm damage and needs a little help. The rudder has now been replaced with a new one from Foss Foam (original oem and they did an excellant job fabbing a new one) but I am now looking to the pulpits and lifelines. Does anyone know who built the original...

In preparation for some cruising, I have replaced the pushpit on my E39 with an arch, and I'm thinking that some E39 owner out there with a bent or otherwise janky pushpit could really use the one I have, since it is in excellent condition. It could use some cleaning and polishing, but I...

I recently purchased an Ericson 29. There is some work that will be required and I probably won't put it in the water until next year. The first item on my list is to recore a portion of the bow. The reason I have to do this is somewhere along the line the bow pulpit was ripped out leaving...

Can anyone tell me why Ericson produced some E27's without stern pulpits? Were these intended to be raced?

I'm looking for a bow pulpit for my 1971 E-29. The existing pulpit has been modified by the P.O. to support a folded tabernacle mast, and althought well built, doesn't follow the lines of the boat. Thanks, Ray Hughes. (rayjay3@sbcglobal.net):egrin:

Due to winter damage I have to replace the pulpit. Who is out there and has done a good fabricating job and might have the OEM specifics to minimize the re-drilling of the foredeck?! Thank you, Lee

:egrin: I'm looking for a bow pulpit for my 1971 E-29. The existing pulpit was modified by the P.O. to either brace the tabernacle mast when dropped, or to shorten to overall length of the boat for slip measurement reasons. Thanks, Ray Hughes.

Does anyone know of a source for stainless bow pulpits? mine got hit by a loose boat and is bent all to sh#t. I am located in Maine but will have it shipped for a good quality part at a good price. Thanks Neal Weinstein 1983 E38 Enterprise

just driving ahead here... this fall when i haul out i'm going to need to replace lifelines, as well as possibly front pulpit and one or two stanchions- i guess one can just order lifeline cable from west marine, but where in the world do i go to replace front pulpit?? and perhaps with one...

Where can I find a new/used/or custom order pulpit guard for Ericson 35-2? Must fit on the bridge deck.

Today I stepped the mast after replacing all the standing rigging, compounding and waxing, rewiring etc. The backstay where it attaches to the stern is run outside of the pulpit but rubs some on the pulpit. This was the case with the old rigging too. I cant tell if the shroud should actually run...

contact weinlaw@maine.rr.com. neal weinstein

Hi, I'm looking for a mast for a 1973 E-32. I'm also looking for a bow pulpit. Please email me if you have one. Thanks, Duncan

I recently acquired a e 27 and am looking for a used mainsail in good condition and a bow pulpit. Please contact me if you have any ideas for me :egrin: .

Just getting into renovating a 1976 E39. Any ideas on where I can go for a new bow pulpit? If you have one you're looking to sell, you can also email me, danwalker4 at comcast.net

My stern pulpit rail has cracked in half at the top of a stanchion. can it be fixed or do I need a new one? What costs are involved if I get a new one. Thanks.

I need to replace the bow pulpit on my 1981 Ericson 36 Ron Holland. Anyone out there with ideas where I could get one? Steve