sole

are Ericson soles glued down? I own an Ericson 38 200, moored in Marina Del Rey, and am trying to replace the shower bilge pump hose. nfortunately the original hose (I assume it original) has deteriorated and when I try to pull on it it disintegrates in my hand. I’m trying to lift the floor...

Like most of us, I have water which regularly enters the boat through the mast on my E32-3. There is no gutter around the mast step so the water runs across the cabin sole to the starboard side of the boat and seeps into the edge of the flooring where it meets the fiberglass gelcoat at the base...

1972 E 35-2 with- Fiberglass sole (white) Engine location under dinette seat Fiberglass inner hull ceiling style issue: the sole creaks from end of couch (to aft end of sole behind entry stairs. original design had 2 1.5 thick ply pieces spanning cabin laterally (1 at end of couch, and 1 at...

It would appear that there are two 1/2" thick soft iron braces/brackets/crescents (I'm certain that there is a proper word for these structures but the mind fails me at the moment) that are glassed into the hull spanning the cabin sole. One is below the bulkhead separating the galley from the...

I've used nothing but Cetol on the sole for many years. The sole is physically in great condition, but the Cetol is leaving a dull, yellowish finish. Suggestions for an alternate? Surface preparation required?

Hello all, I'm in the midst of replacing the sole on my '81 E28+. I had a few soft spots that weren't getting any harder, plus some water seepage from an unknown source appearing at the bast of the galley, so here we go: The floor came up in strips, chips, and fibers, much as has been...

I had a '84 30+ surveyed yesterday and heard that a small area of the cabin sole at the bottom of the ladder gave a little under full body weight. Any thoughts on level of concern, possible causes and remedies would be very helpful. Thank you. Peter S

What is the thickness of the existing sole on our boats, 1/4. 1/2. 3/4. Is the sole the standard 2-1/4 teak and 1/4 holly? It there a supplier that you would recommend? Thanks in advance

I have an E25CB without an inboard. The space under the cockpit sole currently only houses the water tank and battery box. Access is via a small door under the cabin steps. I'm considering ripping out the water tank/battery box and installing an access hatch or two in the cockpit sole. I'll...

Well guys, I need some advice on drying out the cabin sole in my E31. I had an unfortunate "hatch open while using the hose" situation, and water got into the cabin, and is between the wood veneer of the sole and whatever is under it. I REALLY don't want to tear out the wood sole, so does...

Location : Catawaba Island, OH On the hard , stern down, water has filled to half way up the length of the bildge cover. Pumped out okay, varnish has whitened, a bit of scum and water to dry out. No signs of any leaks forward of the water line on the sole. Any ideas as to what to do next? What...

http://www.wbryant.com/StellaBoat/Projects/cabinsole/2009/index.htm another of Wally's projects -- this time one that's near and dear to the hearts of Vikings. Loren

This was done 2 seasons ago but with the wintery weather we have this weekend, it is a good time to catch up on my project descriptions. Here is a link to my projects website: http://www.tkronaboat.com/Projects/Ericson%2035%20Projects/Cabin%20Sole%20Replacement/index.html And a nice photo...

Hi , I'm Having A Moisture Issue In The Forward Cabin Sole/right Side. The Area Is At The Beginning Of The Flooring , As You Stand In The V-berth Area. My Main Issue I Can't Seem To Access Under This Area To Correct The Problem. My Boat Is A 1989 E38-200. I'd Appreciate Any Imput . Frank

I recently had our boat (E-27) trucked to our club with very few (I hope) problems. I hadn't secured the folding table properly and came down in transport creating a crack in the cabin teak. I have corrected this but am more concerned about a new squeak/creak in the cabin sole. The sound...

I'm looking to replace the teak and holly sole in my 88 Ericson 38-200. It's worn in some places, esp at the seams, there's some water damage near the mast and in the galley from the dogs water dish, and some general dings and stuff. So, thinking that I'd rather be using my vacation time for...

My E35 had an old carpet that I need to replace. I would love to have a holly and teak sole, but it seems to be quite expensive; my online quote was about $3100! I am wondering what others have done to improve the interior. A guy on my dock said he cut his own carpet and spent about $50.00...

So I have been able to get the factory sole up, actually with greater ease than I anticipated, although not intact enough to use as a template. I am making templates out of 3/8 plywood, to get some practice and to make sure things fit before chopping up my teak and holly plywood. QUESTIONS...

:dunce: Replacing cabin sole on 30+, inspired by all the posts on this site. I am all set to start cutting the replacement pieces. I've got the 4x8 3/8 plywood teak and holly veneer. Plan to use a router to make the cuts. If I could somehow remove the existing sole without tearing it to...

Would anyone have a piece of old teak and holly sole leftover from a new sole project? I just need a piece to replace a bilge cover, and I'd like to get that weathered look, so it somewhat matchs the rest of my sole. I'm not sure of the exact measurments just yet, it's for a 1982 E-38, it's the...

When removing the cabin sole from my '85 35-3 I found some sticky tape like substance at all the joints where 2 different pieces of the plywood butted up against each other. Can anyone tell me the purpose of this? Reduce squeaking? I would think this might cause the joints to rub together...

Today I cut all but 2 of the pieces of teak and holly to install for my sole. I rough cut all the pieces with a circular saw and then used a router to cleanup the edges. As you can see it looks pretty good but I still need to install the trim and build the access panels. I will also install a...

All, Recently discussions of the large Bomar hatch some of us have fitted to our cockpit soles caused me to check eBay for one and geuss what? Here's what I found 250092792522. If any of you are considering doing this to your boat, you just might get lucky if you bid smart, once and very...

Two weeks ago I bought a lovely 1982 E-38 that hadn't had much attention in the last five years. I’m sure this won’t be my last request for help… A long time diesel leak has soaked the cabin sole. The sole near the engine disintegrated (and the wood structure under the aft birth has to come...

I am finally at the point of finishing the cabin sole in my basement and have a number of relatively large scraps of 3/4" teak and holly marine ply leftover from the job. I used 2 4X8 sheets for our E33 and the scraps now add up to most of one sheet. The biggest piece is about 1/3 of a full...

hello everyone...chip here again. i just wanted to know where i can get a replacement hatch for our ericson 25...im not sure what you call it,,,,but its the hatch you slide back to enter the cabin.... i looked up pacific seacraft and got no where....mine was redone in wood by a previous owner ...

I posted this when I removed the cabin sole in March. http://www.ericsonyachts.org/infoexchange/showthread.php?t=3064 The new sole was installed in May. It was made from 1/4" Teak and Holly marine grade ply and finished on both sides and edges with two coats of Smith's Epoxy. It was...

Reading through the E32 threads, I read about some blistering problems on some Ericsons that where manufactured in Mexico. The years of the boats are that of what I'm looking at. Is this a real problem or is it a lot of hype? Would the serial number tell anything on where it was manufactured...

Does anyone have any experience with replacing the teak sole. I'm in the process of purchasing a 1989 E32. But the floor will have to be replaced. Other then that, the boat seems to be in pretty good condition. It seems the floor was glued down. Is their a reason it wasn't screwed down? Any info...

I've been told that the cabin sole on our E-38 is too thin to sand for refinishing. What's the best way to refinish the teak/holly sole?

My cabin floor is in fairly good condition. However, there are areas close to sections in which installations were performed, showing scratches, and drops of epoxy resin. Any suggestions on: 1. Removing glue, epoxy and other glue-like residues. 2. Removing scratches. 3. Fixing small areas in...

I would not have attempted this if not for the wealth of info on this site. Many thanks to all who have contributed. As can be seen in the attached photo's, my sole is in pretty bad shape. It has been covered by a rug for many years, but it really needs to go. I recruted my wifes cousin, master...

A local yard has suggested that if I were to remove my teak/holly sole, I would find a solid fiberglass floor...perhaps the teak/holly was a factory option. They also suggest that if I were to decide not to replace the teak/holly, that I could refinish the fiberglass sole and have an acceptable...

I have finally decided to bite the bullet and replace the teak & holly sole on my 21 year old E38 (it had gotten wet underneath and delaminated in places). Fortunately it is not glued down to stringers. 1. What is the best way to remove the teak plugs covering the screws on the perimeter trim...

I took out the cabin carpet of my E35-2 and found the fiberglass floor to be stained. Thinking about having a teak and holly floor to cover it. I'm not a carpenter, but can do some pretty basic woodworking. QUESTIONS: Is there an existing cabin sole template for E35-2's that I could use to...

Does anyone know a solvent that is safe for fiberglass and can remove the strips of glue used for carpet backing? Thanks in advance. Steve.

Hello again, What do you guys have to say about redoing the teak and holly cabin sole? I know you have to sand it down, but thats all I know!!! What kind of finish, how may coats... anyone done it? Chris

While reading all of these sole replacement threads, I was reminded of my recent musing about sole refurbishment in our E-27. The 27 has a molded fiberglass sole which we have covered with a carpet. The admiral and I have long lusted after the teak & holley soles we see in other boats and were...

Athough the recent string about sole replacement was amazing in regards to the information provided, I have a question that would be most easily answered by those brave souls who have removed and replaced their soles (hey, you can't blame a guy for a bit of linguistic license!) on a late model...

Unfortunately, my boat is one of the models where Ericson glued down the teak and holly sole. Has anyone ever removed it on a similar boat and how big of a job is it?

My 1981 E35-2 has the optional 25-gallon metal potable water tank under the cabin sole. The tank is located on the centerline and runs from the aft end of the forward settee bench to forward edge of the aft settee bench. The tank has sprung a leak and the Fleet Admiral :wife: has decreed that...

I'm concerned about the cockpit sole, seems a little soft on the forward end. Does anyone know off-hand, if it's solid glass or sandwich balsa?

I have a '86 Ericson 32 where the cabin sole is not screwed down but appears to be glued. This flooring needs to be replaced (warping, rot, etc). This means a rip/destroy action. Any experiences, do's, don'ts, suggestions for me before I start?:confused:

I have a 1985; 32-300 My flooring around the mast has delaminated and generally rotted an area about a foot square. Rot has also wicked up the side of the adjacent locker. Rain water evidently accesses the inside of the mast and should be routed to the bilge via a coffer at the base of the...

This was our first year with our first boat, a 1986 30+. We learned a few things the hard way, like properly stowing items so that they wouldn't go flying across the boat and create dings in the teak and holly sole. (Actually, in our defense, the lockers need new latches, so the first couple of...

Hey Guys / Gals: I have a question about the sole material. My E26 looks like it has just a plywood floor with grey epoxy paint on it and is fiberglassed in on the sides where it meets the hull. Was there a teak and holly sole there originally that has been removed or is this the original...

We have an 1987 E34 and, as you might expect, there are more than a few on-going projects to maintain and upgrade our boat. BTW, thanks for all the info on Cetol - I too dislike the orange color and will be refinishing the exterior brightwork in the fall. Another project is...

I'm a new member to this exchange, I was tickled when I found it, terrific source of information. I have a 72 vintage E29, been doing a lot of upgrades (headsail furler, repower, new teak hatches, Awlgrip). At the end of the day, it's cost effective to maintain and enhance rather than to...

I started sanding that corner area of the cabin sole in my head last night, and the teak there is/was black. I knew that there was some water damage and rot in that area, however I don't think I need to completely replace it just yet - but I would like to refinish it (the entire cabin sole)...

* This message was a secondary message to E35-3: "Stains and Rot in Teak" - also posted. --------------------------- I'm looking into purchasing a 1986 E35 MKIII, and have problem. This boat has experienced some leaks somewhere in the coach roof area that ended up running down the...