EricsonYachts.org has opened the season for raising funds to support the expenses of the site. If you would like to participate, please see the link below for additional information.
Thanks so much for your continued support of EricsonYachts.org!
Hello! Total newbie here but hoping someone might be able to answer this question about my recently acquired 1975 32-2 Hull #323 with a 3-cylinder Universal (?) Diesel:
There's a non-working fuel gauge by the RPM gauge and throttle, but I can't seem to find a fuel level sending unit anywhere on...
I recently bought a e32-2 and was amazed by the prop walk in reverse. ain't never seen that on an outboard. . .
so my question is has anyone tried using a ducted propeller to minimize prop walk and optimize the output from that tiny propeller.
i must also say that the westerbeke 2 cyl diesel...
Injectors and glow plugs
Just yesterday I replaced all 4 Injectors and glow plugs on my Universal 5432. I started and 7:45am and was done by 11:30 am. It’s fairly easy with all the right tools. I removed the intake manifold as it makes the job much much easier. I bought 4 brand new injectors...
PRICE REDUCED 4K 09/06/17
This boat is in amazing condition and is completely set up for cruising. This is quite possibly the best equipped Ericson 29 on the planet. Built in 1972 with super thick fiberglass.
She recently made the trip from Long Beach, CA down to Huatulco, Mexico and is...
I feel silly asking this question, but where do you check/change the transmission oil on the M25 engine? I have an Ericson 27, so it's a bit difficult to access as is. I found a likely-looking bolt on top, but didn't want to go tearing into things without knowing. I have the short technical...
Fierce Grace is a 1972 E35, I am trying to figure out that year the engine is. It was re powered with a Universal, does anyone know how the serial number breaks down to find the year of the engine? Thanks.
Hi out there,
My oil dipstick broke off about six inches from the end (which end now sits in my oil pan). My engine is the 32HP Universal diesel that came with the Ericson 38 in 1984. Anyone know where I can get a replacement dipstick and if there is any danger in leaving the broken end in the...
Have you seen or heard of anyone converting to saildrive on an E35ii (or similar)? I don't think it would make sense on the mid-engine/under dinette models since the keel would be in the way. However, I have an aft-engine/under companionway model...
It seems that most people that have sail...
Ericson 30-2 (1979) with transom-hung rudder and wheel steering for sale in San Francisco. Good condition - ready to sail. Inboard Yanmar diesel (rebuilt this year); double spreader rig; North sails - less than two years old; self-tailing winches; spinnaker with pole and lines; Harken roller...
Because the archives are currently not available, here are Tom Metzger's
notes on upgrades and recommended changes to Universal diesel wiring:
UNIVERSAL DIESEL WIRING MODIFICATIONS
During discussions on the Sailnet Ericson e-mail list about wiring problems with
Universal diesel engines...
Just posted our ad for our 1978 Ericson 36C. Asking $24,900 - with lots of new additions and upgrades! Thanks for passing on to anyone you know might be interested!
I have had the engine on my 1987 Ericson 28 since I bought it 3 years ago. I do not know the hours. I usually run it no higher than 2100 rpms. But it started giving me a bit of mostly-white smoke. I ran it at 2300 rpm and more smoke came. Looking for an experienced skipper to tell me if this...
Hi all, after paying for a rebuild I think I have decided I want to go for more horsepower. The engine is being rebuilt on Shelter Island in San Diego and should be completed by weeks end. Includes a 6 month warranty and the control panel as well. Holler if you're interested or want more...
I have just pulled the FWC diesel from my E29. I want to sell the boat but it seems that sailboats are worth more their parts than as as a whole. This diesel was installed new in 2003 and current hours are unknown but must be low as little use was incurred before I bought the boat. This an...
Does anyone have any first hand experiences with the 16 HP 2 Cylinder Yanmar which was a replacement motor for some of the 30-35 foot Ericsons? I don't have a model number but the one I am referring to is the raw water cooled version.
This probably belongs in an existing thread where access to an existing diesel tank was discussed...
I cannot find such a thread with short search, so here is the link with a number of helpful photos.
http://www.threefools.org/velocity/Projects/DieselAccessPlate/DieselAccessPlate.htm
Loren
I've had problems over the years knowing when my fuel tank is actually full. Yes I have a gauge and it does work. It would be nice though to see when the tank is full and I was wondering if it would be possible to replace the diesel fuel filler hose with a thick clear plastic hose. Or maybe just...
Diesel filter question.
As some of you may have read, about a month ago I thought I was going to have to replace my fuel tank. After replacing the old narrow copper lines from the tank with new rubber hoses and new barbs it seems to be okay.
My question is that for the past 9 years since...
A fellow boater asked me recently if I knew about diesel coolant for his freshwater cooled engine. I haven't heard about that, and have been using regular vehicle rad coolant, mixed 50/50 with water to add to the cooling system in my Universal diesel engine. Does anyone know if there is a...
We would like to install a diesel cabin heater and read with great interest an article we found here (or linked here) called "Sealing Deck Penetrations to prevent core rot" It was very good advice with regard to screw holes, but we are needing a 3" hole in our deck to accommodate a diesel cabin...
Wasn't there last week - at least 10 gallons - no leaks around any lines going to engine...
Tank had to have sprung a leak? :mad:
Only one other possibility; We were changing out the float style fuel sending unit for a new Centroid capacitance sender. We were using a vacuum to keep debris out...
What do you all use to clean your engines? What are the best results and what do I need to look out for?
http://picasaweb.google.com/m/viewer#photo/CSMckillip/5405606617022603825/5430887646435156530
Can anyone give me input on the useful life, in operating hours, of the diesel engines on '88 Ericson 38 sailboats, assuming reasonable maintenance: oil changes, etc.? I have about 5,000 hours on the engine [mostly light duty motoring in and out of the marina] and need to replace the...
After sitting for about 2 years with diesel fuel biocide and additives, I hired a diesel mechanic for preventive maintenance which included: Adjust the valves, check the injectors and generally inspect the motor. Afterwards, the motor in neutral spins to 2,900 rpm but only 2,200 under load...
My '83 E28+ inboard diesel engine (original, but apparently serviced extensively a few years ago) started running very hot toward the end of the summer... getting up to 220 after only 10-20 minutes with little throttle... added antifreeze and it helped tremendously... the motor would run at...
Hello,
I noticed water dripping from the bottom of my raw water pump on my
Ericson 28+ Universal model 5411 diesel. I bought new gaskets and a pair of
the round metal replacement seals to see if that would solve the leaking. I
would like to know if there is any thing special I...
I have a ericson 27 with a gas 4 cyl Palmer
It has problems
I can get a volvo 2 cyl 13-14 horse with trans that is available
Will this motor have enough guts to back me off mud or sand
bars if necessary.
ChuckA
Hello All,
I was wondering if there was a difference between the diesel fuel you get at the local marina and the diesel fuel you would get at the truck stop. If there is a difference what would be better for your boat diesel auxiliary?
Thanks,
Brian
E31C Nemo
Metro Detroit
Hello Everyone,
I've been away quite a long time, but I'm back with a quick question. Does anyone have a diagram of the pathway for the large exhaust hose on my Universal Atomic Engine. I know it runs unseen under the sole near the shower sump basin, then disappears behind the cabin ladder...
Hi all
I sold my E 27 last March and I am seriously considering an E 28. It's located in Warren Rhode Island, been in the hard for 4 years. I live in Massachusetts and I am looking for a recomendation on a mechanic to fo through the motor before I close on the deal. If the motor checks out...
During the gloriously hot weather on Sunday my fuel take overflow valve started to leak diesel. I filled her up end of season last year when it was pretty cold out but I would not expect expansion enough to overflow the tank????
Hello all. We have a M25 Universal Diesel with 2600 hours on it which I suspect is the original engine from 1986. It starts and runs well. Doesn't leak, overheat or misbehave in any way and I keep up with oil changes and filters. I'm wondering just how much life is a reasonable expectation for...
Our 30-year old aluminum diesel tank has no access or clean-out hatches. It is an 80 gallon built-in ... literally, it extends under cabinetry and (partial) bulkheads.
I can see how to cut access hatches in the teak (plywood) sole and make that work well.
What I am much less sure about...
We just had our E39-B polished and waxed ... very nice :-)
Of course, as soon as we started up the diesel after the "service" we got a black streak running down the hull at the stern. My gut reaction is to try to attach a 1" (or so) extension to the exhaust to keep the sooty drip from...
I'm looking to replace the old princess alcohol stove oven in my E39. It has never been set up to use propane.
I saw a new-design Wallas Safeflame diesel stove from ScanMarine (in Seattle). They have several designs, and some have a blower kit that turns the stove into a cabin heater.
It...
Folks,
Just bought a '79 e29 that was converted to diesel from gas (in '87) and discovered that water separating fuel filter clearly states "gas only" -Racor S3213. Previous owner who had her for 6 years never changed the filter - should i worry? Should I replace it with appropriate made for...
Has anyone ever found a place that sells replacement caps for deck fills for Ericsons? The replacement caps from West Marine and so on don't fit (wrong threads). We'd like to have a spare one handy. We have an 80s E34. If a cap did get lost, the only solution would seem to be getting a new...
Yup, I dropped a SS screw (1 1/4" 10/32 just to give you some idea on size) into my diesel tank while replacing the sending unit last weekend. AAARRRGGGGHHHH!!! At least I didn't drop the SS "C" ring that I bought along with the WEMA sending unit. I tried to retrieve it with one of those claw...
Hello Vikings
Our new boat(Catalina 42) has a Yanmar 50hp Diesel. My 74 E35 MKII has had an Atomic 4 gas engine all these years so I have never had to learn about the care and feeding of a marine diesel engine.
Where can I find info about additives? I have talked to people and they use them...
http://www.ericsonyachts.org/infoexchange/showthread.php?t=3404
http://www.ericsonyachts.org/infoexchange/showthread.php?t=3585
http://www.ericsonyachts.org/infoexchange/showthread.php?t=6266&referrerid=28
What with several recent threads about fuel pumps, filters, and the mention of fuel...
For those of you with a Yanmar YSM 8 or 12 Diesel I found a link online to the service and maintenance manual.
http://www.swinranger.co.uk/yanmar.htm
If someone can tell me how to upload this I am more than happy to create .pdf's to add to the "specs and documentation" section on this...
John Featherman (http://www.feathermanenterprises.com/index.html ) has added a nice little basic diesel engine trouble-shooting page to his web site.
http://www.feathermanenterprises.com/faq/dieseltroublemain.html
Perhaps someone here will find it helpful.
Loren
(no personal or...
In doing my spring clean-up in my 1983 E-28+ I found that what I thought was a small amount of spilled engine oil in the bilge turns out to definitely be diesel fuel (the odor is a dead give-away). There is no oil in the engine compartment beside some that I had previously spilled, and thought I...
I need to change my anitfreeze in the Universal diesel engine. What is the best antifreeze/most popular antifreeze used in diesel engines by Ericson owners?
John
Laiva
1984 E 381
Sells for about $650 new. Asking $425. I have some addional hardware that goes with it that I may throw in or sell for a good price...I forget what else I bought with it.
Details on the stove can be found at http://www.boatownersworld.com/dickinsonmarine/newport_diesel_heater.htm
Hello All:
After a couple months of elbow grease & TLC, we are on the 1st voyage on NAKESA, our new 1988 38-200 (with a Universal 32 hp), & have a perplexing problem.
The engine bilge is filling with about 1" of liquid - pink in colour & a bit oily - could be diluted diesel - source is a...
First of all thank you so much for this great web site. :egrin:
I have made two posts regarding my 28 "Seize The Bay". I have learned so much and gained confidence to fix things myself. A very big deal for this 48 year old woman! I would still be paying BIG mechanic bills if not for this site...
Hi all,
Anyone have any experience with Universal 10 diesel ongoing engine troubles? Seems our 1985 engine does not like to work. I have had my 1985 28+ for six years. Five of those years have been spent trying to find out why the engine always stops. I have reduced my sailing to only in the...
http://www.soundmarinediesel.com/q_and_a.html
I was doing some 'net surfing and reading up on Diesels and replacements ... after following another thread on this site about repair vs replacement.
This site FAQ seems to have a lot of good commentary and advice, at least based on my limited...
Two weeks ago I bought a lovely 1982 E-38 that hadn't had much attention in the last five years. I’m sure this won’t be my last request for help… A long time diesel leak has soaked the cabin sole. The sole near the engine disintegrated (and the wood structure under the aft birth has to come...
My fuel tank recently failed on the "Dawg" and replaced it with a 23 gallon Black poly tank from West Marine.....fairly easy replacement BUT:esad: I can't seem to get the diesel smell out of the boat. I've tried several applications of bilge cleaner as well as a host of cleaners from the local...
Since Sean has designated this forum for 'mindless chatter"... This might qualify.
Afternoon before last we hauled the boat for a bottom job and some drive train maint.
Freezing weather has been here for the last several days and the yard (quite properly) wanted to know how I wanted to protect...
Hi All -
Well, two weekends after beginning the replacement of my Raritan Water heater, I finally have the new heater in the lazarette and ready to install. What an interesting exercise that was - they must have put the water heater in before they built the boat, as it was much larger than...
This was given to me but I already have one..
Covers models: M12,15,18,20,25,25XP,35,40,and 50
light greasy fingerprints on the cover but otherwise great condition.
$10 includes postage.
Please reply directly to jsmeier@yahoo.com
This was extracted from another list that I participate in.
"For those of us who prefer to burn clear road diesel vice the dyed
marine diesel (easier to monitor particulate and microbial
contamination) , note that as of October 2006 the EPA has required
refiners to produce "ultra-low...
Last pump out of the year, plus top off the diesel.
It's cold out, I have my son with me.
Harbor is busy, so we tell the attendent we can take care of it ourselves. I'm working on the pump out, my son on the diesel.
I had a small air leak at the waste vent so I started running water over the...
I put my engine on ebay if anyone is interested.
Running Takeout, removed from 1982 - Ericson E36 (8-14-2006). Universal Marine Diesel 5424 (24hp) with Hurth transmission (2:1). Complete with instrument panel (not shown) Fuel, Oil Pressure, Alternator gauges. This engine runs fine I decided...
My Racor fuel filter had a gasket leak for some time and the diesel fuel has dripped onto the mahogany side panel that covers the diesel engine. I am in the process of refinishing the wood and can’t seem to get out the diesel fuel from the wood. It has a wet stain and is saturated. So I...
As I live about 1,000 miles from where I moor my boat (that will change when I retire), I always need to think ahead for maintenance work and upkeep, as I don't always know when I will get there again.
My question: I will not likely sail from October through March, and want to do what's best...
My 1983 has a 12x10RH prop. After replacing the cutless bearing, shaft and coupling half this winter season, I now discover that the prop tip clearance is 9.2% or 1.11". From what I have learned the tip clearance should be 10% - 15% of prop DIA. What size props are the rest of us E25's...
Hello
I have a 1982 36(RH) that I'm repowering with a yanmar (1994 3GM30F) engine. I hope to go cruising someday and want an engine with a more availible parts supply. So my current 5424 (24hp) with hurth trans and control panel is for sale. I do not know how many hours are on it. It...
I am in the process of installing a BETA 920-25hp diesel auxilliary
and want to install a new fuel pump and keep the old FACET pump for a
spare. The only pumps I can find are Facet-Purolator and Walbro :confused:
Anyone recently replace a fuel pump ? Would appreciate a heads up on this...
Hi All,
Have any of the E35/3 owners installed a diesel heater on their boats? Currently I have an Espar forced air heater but I would prefer a free standing diesel heater as I hate the noise of the Espar. I was wondering if anyone had one bolted to the floor between the mast and the...
If anyone out there has installed on of these heaters, I would appreciate information on what flew length was used and how low you placed it on the bulkhead. To get the factory specs, I need to mount if right above the cushions. I can remove the cushion when using it or mount it higher and...
Hello,
I have 1986 38' 200 with the 5432 Diesel above. I've broken the throttle bolt going through the speed plate, which is at the top of the govenor (I believe that's what it's called). I've ordered and received the new bolt and related parts for the repair. My question is has anyone...
I have an older E38 and I am going to add heat this fall. Been looking at mainly Espar and Webasto forced air systems. The large ducts and the compromises involved in routing them in this boat are causing me to re-think that idea and look at water systems. One advantage of the "hydronic" systems...
I saw technical literature on this somewhere most likely on this list, but I couldn't find it with the search. Can anyone providing the engineering rational to justify and/or dismiss aluminum, Stainless, or plastic.
thanks
shaun :confused:
If you want to quiet your noisy diesel engine, I would like to introduce innovative and easy-to-install soundproofing tiles that we designed for marine diesel applications. The tiles have been use by hundreds of satisfied yacht owners. Here are some features:
You can find more at...
Used diesel, runs well. We bought it to replace a dead Atomic 4, but found it doesn't fit our boat. New alternator, improved alternator bracket, new fuel pump, other upgrades. Asking $3500. Email rschaffner@gmail.com for more information.
:confused: I have an old Yanmar YSB-8 that has not been run much this season. Today it started fine as usual but when put under load it released an awful lot of heavy black soot onto the water. I ran it this way for about 20-30 minutes and it continued. It was not oily at all, just soot. At...
I have a 76 Ericson 35 with a rebuilt atomic 4 that is about to go bad. Does anyone know which diesel is the best repalcement for the MKI? My engine is under the dining settee.
Can anyone recommend a good diesel mechanic in the San Francisco or east bay area? Hopefully one which would have some time available in the next couple weeks. We keep our boat in Berkeley, and she has a Perkins 4-108.
Hello,
I've got a defective diesel sender unit and wonder if anyone can suggest where I can get a new one for my 1986 38-200. I posted this message before without checking the box to allow email responses. Pretty dumb on my part. So please do consider this a new post. Thanks.
Frank Z.
Has anyone got a Diesel in an E27 and what model is it? I have an atomic 4 that sat full of water for a year until I recently bought it. 2 pistons were siezed and half the valves are rusted to the guides. The carb and air box are missing, and the piston rod ends are way too sloppy. It needs a...
First, let me say I am stupid when it comes to engines. I have a very slow leak at the 1 1/8" (1 1/4"??) diameter engine fresh water drain plug. It has a smaller plug within it, but does not seem to be leaking there. If I back it out a small amount and put polisulfide caulk on the threads and...
I haven't hooked up my used Yanmr diesel yet, the engine is inside the cabin on the sole. It has test hoses attached to the engine for fuel and water, which were used to test starting.
I'm in the northEast, and wish to know, should I just blanket the engine, to insulate?, or does anyone think...
:egrin:
i am in dire need of a metal cap for my deck filler that has a fine thread and is adaptable to my original diesel deck filler assembly.
any ideas???
I read several reviews for E26 that says the boat has 10 hp diesel engine and a fuel tank. But my newly acquired old E26 is powered only by an outboard. Do we know if my boat used to have a diesel engine which is removed later on? Or my boat could've been built without an inboard engine?
Searched past posts and can't determine if there is any problems using "truck stop" diesel versus on the dock "marine" diesel.
Thanks,
Steve E35-3 #159
I am wondering what folks use for the fresh water cooling circuit in their diesel engines: 1. Pure antifreeze, or 2. 50/50 mixtue of antifreeze/water, 3. other. Peter
Hello All!
I have an Ericson 25+ with a Volvo Penta MD5B/110S engine. Couple of quick questions...
1...After replacing injector, engine runs about 30-60 minutes then shuts down gradually. Air is entering the system? After bleeding the system (especially at the injector pump) it runs...
I have a 35-2 with the u shaped dining plan. Translation, the engine is under the seat with no clearance for a taller engine. Does anyone have any advise on an engine choice for this situation. I don't want to have to reconfigure or raise the lid noticably because my boat is sort of bristal...
I have the 35-2 plan with the engine under the dining seat. I would like to switch out the old Atomic 4 with a diesel. Has anyone accomplished this and fit it in the existing box without cabinet modifications? If anyone can shed light on the best engine to select and what I can expect in terms...
I got a real yanmar manual from Richard for my 1GM. He was real good about returning email on availability and price. Austrailian dude.
minards@comcen.com.au
I have a question -
Can anyone tell me where the best place to buy diesel is in Commencement Bay (Tacoma)? Since I've had the boat, I've only topped her up three times, and that was once in Everett and twice at Shilshole in Seattle.
I'm just wondering if there's a preferred place with...