e27

So last week, while out doing some maintenance on the boat, my slip neighbor offered me a nice cold one from his mini fridge on his powerboat and got me thinking. While I don't think I will be doing any long distance cruising on this boat, I started researching this site and read all the...

My locker goes all the way to the bilge and is open to the engine (removed by PO) compartment. Needless to say, if you throw something in there, it goes a long. way. down. Can anyone send along pics and designs of the original locker compartment config or any useful modifications?

I need to replace the sending unit on my 1978 E27. Has anyone done the same and have any advice on pitfalls to look out for. I'm also wondering if I need the exact part or if there are universal units. I'm hoping to get the part before removing the current unit. Thank you in advance, James

I had a reputable local yard look reveiw my mast and tell me that I should be looking for a new one.:esad: This is something I will consider at least until I get sticker shock. Has anyone replaced an E27 mast? If so what mfg. did you go with, what mast section, cost, etc. I've looked through the...

Just got a great new Video Camera with a Ultra Wide Lens. This was just a test I will post others soon. Enjoy :egrin: It was a great evening sail. http://videos.sorensonmedia.com/d0024e39-0c5a-4991-bb5f-f3d8a6e7bc16/E27+Ragamuffin++Sailing+on+Lake+Michigan/4235e338-662a-417f-81ad-b421d4b41f23

Does your E27 have 1 or 2 access hatches for the bildge. The PO installed a laminate flooring revealing only one hatch under the companionway stairs. However, I recently noticed a "soft" spot just aft of the bulkhead. Yesterday I saw a photo of another E27 showing access hatch in this location...

I also posted this over at plasticclassicforum.com. I've been thinking about this on and off over the past year, and now is the time to really figure it out. The mast is in reasonably good shape except for the area around the spreaders. There are a bunch of excess holes, and the old...

Hi everyone, Wondering if I can get a little assistance with a jib purchasing decision. I'm considering the purchase of a jib with dimmensions of: Luff: 19.25 ft. Leech: 15.67 ft. Foot: 9.5 ft. I know this is less than the 100% area available in the foretriangle created by the...

I have a Ericson27 and I want to install a Halyard so I can use my spinnaker. My question is what do I need to install to make this work? And how would I fasten a block to the top of my mast? pictures would be a help. Thanks for any help Roy9216 <!-- / message -->

I just launched my e27 last Monday. The boat has never really taken on much water before, but I noticed that the fore keel bolt area (where I think they originally attached to lift the boat) has a slow leak. I dry the area out and notice it just slowly fills back up again. I have gone weeks...

Looking for some advice, pictures even better. I am considering modification to my E-27, with wheel steering, to bring the main halyard aft for single handing. My initial thought was to buy a winch and locate it within reach, but not sure how necessary that is. I am fairly new to sailing and...

Hello does anyone have information on where I can get a new/used scupper drain? I have a 1977 E-27 and need port side scupper drain. Please respopnd to dkopp@block.com Thank you.

My 1974 E27 has a manual Raritan head that is original equipment, as far as I know. I've fixed it several times, but its days are limited, and I'd like to replace it with a new head. Does anyone know if there are any manual heads sold by West Marine or other that fit directly into the existing...

Hello Folks, I am the proud new owner of an E27, (berthed in Dana Point CA) I am wondering if anyone has an opinion as to an appropriate tiller pilot for her for occaisional single hand use. the raymarine 1000 says it is good for boats displacing 6500 lbs. This boat lists displacement at...

before and after of the exhaust tubing for my E-27. The before (rusted one) has an obvious flaw that the water from the engine goes into the engine during start up because there is no loop in the tubing. I attempted to fix this by constructing a new exhaust. I need your opinion to make sure my...

Would have posted this question on the recent discussion regarding the Anchor Poll thread. Since this is a specific question, though, I have chosen this format. I am outfitting my E25 for modest coastal cruising and know that it would be smart to include a plow-type anchor in my anchor inventory...

Anyone have any experience or info on mounting a Garhauer motor lift on the stern or transom of anE27. Ron "Bluenote"

Hi All, I am looking to install a Boom Vang on my 1976 E27. I perceive the need to do such when I will be in a following sea with the wind on my aft quarter. I intend to secure the vang to a stanchion base on the appropriate side. My stanchion bases are reinforced with backing plates. The...

Looks like the galley countertop needs to be replaced. The PO let several years of water intrusion get in there and now it's seriously delaminated/rotting. Aside from simply removing it so I can get the pattern for the replacement, anyone have any tips for how to go about this project? The...

Looking for an old beat up tiller to use as emergency steering in place of wheel,has to fit e27 tiller head.

Aloft on my E-27 and other sailing clips can be found on my YouTube page: Aloft: http://www.youtube.com/user/jazapuss#p/a/u/3/UDOT5yai9uE Sailing round the West End of Catalina: http://www.youtube.com/user/jazapuss#p/a/u/0/cep4kXCAgB4 :egrin:

Has anyone replaced a mast for E27, I am wondering what is the ball park cost for such a project? Thanks, Eugene

Hi, I just became a member here today. I have just bought a 1974 Ericson 27' sailboat and will be living aboard soon. I live in Southeast Louisiana and it gets hot down here! I bought a new Webasto 9000 BTU marine reverse cycle A/C unit to put it the boat. The boat is being shipped in two...

I just had my gas tank replaced by a friend - genius of mine ...if anyone cares I could discuss online if you are interested...Beautiful job looks like art. Just want to give back for all the help you have given me....

I hit a rock in a Very Remote Area. After trying to get a haul out (not a chance), I finally removed the Rudder with the boat in the water. After removing the two bolts on the tiller, I hammered it out using a 18" piece of PVC pipe (2-3/8") and a piece of wood. The Rudder popped out, and...

I was sailing from Seattle to California--sails like a dream. For whatever reason, I turned in to catch a good night's sleep before heading back out into the 20' seas. I caught a rock (direct hit on the rudder), and lost helm control. Visually, you can see the rudder bent back. Not taking any...

Just converted Scandalous (E27) from gas to electric. Uses four lead batteries and is capable of hull speed. Using a 48 volt system and cost under 5K for the complete conversion. Located in San Diego. :egrin: Anyone considering this, I would be happy to advise. Don at postal6@juno.com

I originally posted this in the regional board but it was suggested that I might get more responses here. I'm relatively new to sailing and currently looking for a sailboat in the 25 to 28 foot range. Two near the top of my wish list are the Ericson 25+ and the Ericson 27. None are available...

Many with E23s and E25s have outboard motors. Some E26 and E27 owners do as well. I'm curious to know how many owners out there stow their fuel tank (or tanks) in the cockpit, near the motor. The fellow I bought my E25 from stowed his portable fuel tank in the starboard cockpit locker. When I...

I want to re do my cushions on my E27. I'm at a loss on how the wooden seat backs are attached to the wall. tony g. Pine Beach NJ.

My 1976 E27 has an Atomic 4 with an upward loop (galvanized) in the exhaust line at the thruhull in the stern. Any Ericson owners out there have the same setup? I spoke with Don Moyer and he didn't recall any boats using the A4 with this. The reason for asking is I have some restriction...

Just out having a good sail in the cold on Pipe Dreamhttp://www.youtube.com/watch?v=n-Qrdm9TI6M

I need to change the seacocks with newer style ball type on my 1976 E27. I was wondering what kind of force I can inflict the old seacock before doing any damage to the thru-hull. The ones under the sink (engine water and sink discharge) are the worse looking, and naturally have the worse...

Hi to everyone on this fantastic site.I've been lurking here for a while and have finally found the E27 I was looking for.I'll be taking delivery of her on November 18 and sailing back home to the Keys + - 200nm.She is in great shape for a 74 with a good few upgrades but there is about a...

Does anyone have a source for Goosenecks for an E27? I need the slide and the bracket that attaches to the boom. I have tried to get ahold of RigRite several times about it, but get no response back from them. Are there any other sources out there that people are aware of? Thanks, Doug

Hey all - Just popping in to say hey, I (and three of my friends) own Wino Country Safari, an Ericson 27 moored in Seattle's Lake Union. It's a fantastic boat and we love it. Got it for a song and are now starting to figure out the things we want to do to maintain/update it. I've sailed a...

Does anybody have teak decks or synthetic teak decks on a ericson?Im installing Tek Dek now heres a rough draft of what i think it will look like.

My rudder was bent up while tow-boat ripped off cleats and the boat swung aft as it moved. Is there anything between the rudder and hull that I need to loosen or remove to drop the rudder? It is a 1978 sloop.

Just recently finished the purchase of a 1975 E27. She has a Volvo inboard and needs mostly cosmetic upgrades and fresh sails. We are HAPPY:egrin:!!! We hail from Beaufort, NC and seem to be in minority as far as Ericson owners here go. We also really like this forum and love the abundance of...

Howdy all, This is my first post, so please bear with me! I just purchased a '73 Ericson 27 ... to put it mildly, some areas have lots of "deferred maintenance." The hull, rigging, interior, and outboard were all fine (had it surveyed), but there are a few items that need some help (I got...

http://www.plasticclassicforum.com/viewtopic.php?f=37&t=4431 Link to an extensive deck re-coring project on an early E-27. Made me tired just reading it! LB

After a lighting strike that took out VHF antennea, stereo, fuel pump, bilge pump and (expensive) LED anchor and cabin lights, we've been told that the wheels for the halyards at the top of our mast (Shivs? sp) need replacing. Anyone know where to get them? We have a friend with a "mast crane"...

Hello, I'm a new owner of a '76 E27 that although very sound needs a lot of esthetic attention. Hopefully I attached the picture correctly. My first of many questions is about the head. It does not have a deck connection for pump out. There are 2 through hulls I beleive that the larger one is...

My throttle and shifter handles have "disappeared". On a quick look I was unable to find a manufacturer name on the housing, and I don't recall ever seeing them on any supply sites or catalogs. Does anyone know the original manufacture for a 1976 E27 or know where the handels can be found. Are...

I have a 1978 E27, So my engine is getting OLD. It is in need of coastly repair. is it possible to pull the yanmar 1 lunger and use an out board. Or sell the boat. Thoughts please thanx Nic

I'm looking to add a bow roller for my 25lb. CQR. I have neigbor with an E27 two slips down who has a stainless steel roller that has a triangular base, with the roller off set just enough to make room for the standard E27 forestay. It's a great arrangement, but I can't find anything like...

With the help of the EYO "for sale/wanted" forum, I located a pedestal steering system to replace the one the prior owner of my E27 CE (cruising edition) sold off her during a personal economic downturn. Now I have all the components of an old Yachting Specialties system complete with an...

1974 Ericson 27 sailboat. Standard issue Ericson in sail away condition. Original gas inboard was removed (strut left in place) and Outboard Motor mounted in Ericson factory cut-out. 1984 Evinrude Yatchtwin 9.9 hp 25" longshaft w/electric start. Original onboard fuel tank utilized. Motor runs...

Firstly thanks for an excellent website! Having owned an E27 for some four years now, based in the Isle of Man, I've read with interest all the threads regarding these boats whilst I've been continuously upgrading her. Work so far: new sails including roller reefing, new standing &...

Hi All, When cleaning up my E27 after a 1.5 year restoration/outfitting project I was using my trusty ShopVac that sucks up virtually anything and I fear that I may have inadvertantly sucked up the drain plug/strainer from the galley sink. The bag is long gone:esad: Does anyone have any...

I'm looking for a new or used dodger for my E-27. Could also use some sun as well.

All - I just got the email below from a yard guy named Tyler who's working on someone's E27. Could you please take a look and see if you can respond (here and/or directly to him)? Thanks, //sse

I'm considering converting my E-27 from tiller to wheel steering. Has anyone has any experience with this kind of project?

The E27 I recently bought had the helm removed ..... any ideas on where to find a replacement? Does the 27 have a unique helm or are there others that will work? Is the "Cruising Edition" a little rare? :confused:

Buy this beauty and enjoy summer on the Oregon Coast. Docked at Embarcadero Marina in Newport. See details at http://www.seehere.com/runnyknose/ericson27 (click on photo to get full descriptions) Super clean and ready for live-a-board .... great cabin upgrades Sacrifice at $8,000 OBO...

Greetings .... this is my first post .... please be gentle .... Bought a '76 E27 last weekend in Newport, OR ..... it has the split cockpit (but the wheel has been removed) with the main traveler mounted on the cockpit divider. So the block will be at the end of the boom. One of the many...

Hi folks. Still shopping for my next Ericson. Two for sale locally have a near identical cracks along the top aft edge of the transom... you can see a few pictures of one here. I found a description of a very similar problem here. Some exerpts below. Does this sound familiar to anyone...

Hi All, our E27 was built in 1976 prior to the marine pollution regulations so the current system is illegal. We seem to have two choices, either install some kind of holding tank somewhere and cut a hole in the deck for pumpout purposes or go with a portable. We are leaning towards the...

Here in the Florida panhandle my marine stores two suppliers don't carry a 1 3/8 stuffing box hose. Does anyone know where I might be able to find one? Don

I know the topic of the E27 deep bilge with the thin fiberglass at the rear has been discussed on here before. I'm considering glassing in a piece of starboard about 18 inches from the top that would essentially create a "false bottom". This would isolate the bottom portion of the bilge from the...

A standard rig E27. So, the new main is on order and looking at headsail options for the Bay. I've got an inside track near the mast and an outside genoa track alongside the cockpit I'd like to get one sail that sheets cleanly to the inside track to improve pointing. Perhaps a 95 - 105%...

Could someone out there with an E27 that has the outboard cutout in the transom please give me some measurements. I'm gonna be mounting a 25" longshaft OMC classic 2 stroke and need to know where to cut. A simple measurement from the base of the transom to the top of the mounting surface of the...

Hello all, I was extremely excited when I logged on today and saw the thread listing a used E-27 companionway hatch on craigslist. Could I be that lucky? Unfortunately, I am a little late and the hatch has been sold. While I doubt that another will become available soon, if anyone knows...

I recently drilled a through deck hole to install a fresh water deck fill. When I drilled the hole I observed that the balsa core (particularly the forward facing part of the hole) was very damp. Soft to the point I could clean out some of it with my finger. As part of the project I'm replacing...

Does anyone know where I would get a tiller tender for my 78 ericson 27? Thanx

Our P.O. replaced some of the inside cabin light fixtures with some hokey fluorescent fixtures. We still have original fixtures in the salon and galley. When it was suggested to replace fixtures to accomodate LED lights($$$) , we found LED replacement bulbs and are delighted with the brightness...

Has anyone cut out the transom on the E27 to mount an outboard motor like Ericson suggests? I've removed the tempermental Volve Inboard and will either be installing the E-Pod from re-e-power.com or installing an outboard 8-9.9 hp longshaft motor. My concerns will be: 1. Where do I cut? 2. What...

I am looking for a single speed non self-tailing winch with base plate, to mount on my mast for the jib. I don't have much money to spend so need to buy used.

Sliding Companion Way Hatch for E-27 on Craig's List Beautiful Entryway Hatch For 27 Ericson - $200 (Long Beach) http://losangeles.craigslist.org/wst/boa/1087818315.html Refinished teak,gorgeous. This is the Sailboat Junk Yard in Long Beach. Call Valerie 562-200-9108 I actually went and...

Hi all I am seriusly considering racing this season and was looking for advise from others who have raced e-27's or similar E's. I currently have a decent main and 150 Genoa on a roller furling and am looking at a new custom 110 laminate head sail for better performance. Does this make sense? I...

My boat Pipe Dream came off her mooring and got pretty dinged up. Im looking for the starboard rub rail and channel too. Just wondering if someone is sitting on a parts E27. Thank you

Hello, Can anyone recommend a good genoa lead block for my E27. Also does anyone know offhand the width of the track on the 27. I noticed the old schaeffer block was on the verge of letting go so I removed it last weekend but forgot to measure the track for the replacement. I am thinking...

I have a 1977 e-27 the mast seems to be on a hinge, any one have thoughts on the best way to lower the mast? is it a one man operation using the hilards and winches?

I just purchased an E27 and the head sail is less than desirable. I'm looking for a decent used 150 (roller not hank on). Anyone with a good source for used Ericson sails? Thanks

Does anyone have pictures of an E27 with a cockpit dodger? How is the mainsheet arranged? I think I want one but.... :confused:

I am trying to decide whether to install a dodger on my E27. I'm especially concerned about the mainsail sheet operation. Anybody have experience and maybe even pictures?:confused:

Hello All, Any opinions as to whether my E27 stern rail will be up to the task. I have already purchased a Mercury 9.9 four stroke for my new Walker Bay inflatable. I wanted a motor that would plane two....so this was my best option. Unfortunately the thing weighs 85 pounds (one of the...

I amtrying to get a true rating for the E27.I have heard it s243 but that seems too low.

here's an ad for a 1979 E27 currently for sale in California. i thought i'd post the link because the seller has also a posted a really good read on his voyage from San Francisco down to Monterey: http://allstarband.net/Sandpiper.htm note: i have no connection to the boat or the seller.

My new-to-me E27 has gate valves. Could be the originals I suppose. They'll need to be replaced. I've been reading through the messages here about thruhulls, gate valves, and seacocks. As I understand it, thruhulls and seacocks connect with a straight thread (NPS), while one of the issues...

http://boston.craigslist.org/sob/boa/953949644.html It's not mine. I just wanted to point it out in case anyone is looking.

I've got one of the E27s with the cutaway transom. After reading through all the threads concerning cockpit scuppers, connecting hoses, and seacocks, I was almost disappointed to find that my boat has only one cockpit scupper. But it's probably not a problem because any big water in the...

Hi- I am going to be switching my E27 back to tiller steering. The PO put in a wheel in front of the tiller which makes it difficult to move around the cockpit. Unfortunately the tiller fork/bracket and tiller did not come with the boat. Based on some other posts here, I'm guessing the tiller...

I am looking for a used furler for my 1971 E-27. I will also consider buying a genny aready cut for the furler. Will also consider some cash/trade that includes my hank on jib and genny. Please send responses to my private email jgautreau@verizon.net Thanks

Hey everyone- I've started to address the exhaust system on my raw-water cooled Atomic 4 in my 1972 E-27. It looks like its been poorly cobbled together, with a very loose attachment to the manifold (at least it came off easily!) and no support or anchors anywhere. The exhaust exits the...

I am offering "Why Knot," my 1976 E27, for sale. She is currently berthed at Little Creek Marina, slip D-16. I purchased the boat to stay on while I was working in the area, and I had hoped to restore her, but my career has taken me elsewhere. The Atomic 4 will start for someone who knows...

Hello folks, I am feeling a bit overwhelmed with lerning bout my 1978 E27. My survey came back better then average, I have a yanmar 8hp diesel, I have tons of questions about this boat, she sails great even with what looks like the original main. so I need one of those and dont know where to...

Hi- The E27 I recently bought is missing the gooseneck. Has anyone found a replacement that works? I looked at RigRite, and they may have some that work, but I haven't made any measurements yet. Or if anyone has an extra one that they would like to sell, I'm interested. Thanks Doug

Hello, As of 10-8-08, I have a perfectly running fresh water volvo MB 10a inboard motor for sale. Gas powered and 15 hp rated. It is out of my 1974 Ericson 27. Boat has always been in fresh water and only 3 owners. I have removed the motor whole with transmission and placed on a pallet. The...

Hi, We recently purchased a pretty beat up 1972 E27. We know that there is water getting into the deck and seeping down into the cabin at the chainplates. The not so reputable inspector thought the chainplates looked OK but upon my husband's closer inspection they look like they have some...

FYI: The attached photo is of the location of the transducer in my 1973 E27. Note that I used silicone sealant to glue it directly to the hull. The use of a lead line, verified the digital readout while at the berth. Note that the prop shaft (and the Atomic 4) has been removed, as I am using...

Hopefully, this post will give someone some ideas. The attached photos show the anchor roller setup on my 1973 E27. The roller is a WindLine AR-3 model: http://www.windline.com/diagram.html Re: the below deck photo of the backing plates: The large blue piece is 3/8" fiberglass. The SS square...

Since the end of the season is closing in I am getting ready for another fall+spring project. This year electrical. My E27 has an older system that I want to upgrade. Any E27 owners have any suggestions. I am thinking of starting with a Add a Battery system from Blue seas run new wire, then add...

Hi everyone, I recently had my manual bilge pump mysteriously stop pumping. I could tell it was trying to, but just couldn't make the grade. I originally assumed the seals on the pump were bad. I used a hand bilge pump to empty what water was there, and soon enough, IT stopped working...

They forgot to mention the glassed hull to deck joint, whicj is a huge selling point. And the interior pictures are not very good (they don't show the very roomy salon) but overall it's a good review. I did not know there were a bunch of different engines available, I thought most came with...

my 1975 e27 has no fuel gauge, telling me how much fuel is in the aft port metal tank. Does any one know of an economical way for me to occasionally measure the level of the fuel? I'm wondering if some sort of dip stick would work, or something 'sensitive' to density stuck on the side of...

'74 E27 on eBay this AM for $5500 buy it now...................looks clean.

Some notes on the outboard motor installation on my 1973 E27. Photo 1: Cockpit view of one of the two upper motor mount backing plates. Each is a 3" x 3" SS plate Photo 2: View of the bottom of the transom via the port lazarette. Shows the two lower motor mount bolts and the large washer used...

This was just posted today on the Cascadia List (NW Sailing 'net group): "A rather beat-up Erickson 27-footer is going to be sold by auction on August 2nd, to help recover unpaid marina fees. This is in the Seattle area. I doubt it will fetch much money, and needs insubstantial repair to...

I notice a lot of discussion in the Great lakes forum regarding the E27. WHat a great boat. I just did a ton of work on my E27 ragamuffin.(see Photos) Love the boat sails great and now looks great. If your ever down in Chicago drop me a line. I am in Monroe harbor. With about 5 other e27's and a...